Skip to content
Close
SEARCH
CONTACT
PHONE HOTLINE: (585) 265-1020E-MAIL: sales@optimaxsi.com
Careers
Request RFQ
PHONE HOTLINE: (585) 265-1020E-MAIL: sales@optimaxsi.com
Careers
Request RFQ

Knowledge Center

Search Suggestions
    PREVIOUS PAGE NEXT PAGE
    TOOLS & CHARTS ―

    The Estimator

    The Estimator is a unique tool designed to allow you to input parameters of an optic and adjust tolerances to get an estimated cost of your optic. This empowers optical engineers to find the best balance of performance versus cost by adjusting the manufacturing tolerances and evaluating the effect on cost.

    The Estimator is also available through the ZEMAX OpticStudio ISO Drawing. Once you are registered, you can use the same credentials to login (see Cost Estimator in the OpticStudio System Explorer).

    The Estimator is limited in scope to prototype optics within the following boundary conditions:

    • Quantity 1 to 10
    • Optimax Preferred Glasses
    • Diameters from 5 to 100 mm
    • Spheres/ Plano /Aspheres
    • Surfaces of R/1 or slower
    • Standard AR and Reflective Coatings

    Estimator Login

    Optimax currently provides 19 antireflection coatings for the Coating Library in OpticStudio. They can be divided into four categories, which are described below. The coating designs are encrypted, but this article will help you determine which coating to select, and how to evaluate its performance.

    REGISTER
    LOG IN

    For a comprehensive table of parameter limits for requesting Cost Estimates (on this site as well as through OpticStudio), see the table below.

    The Estimator is designed to generate cost estimates with standard delivery in mind. The full scope of capabilities at Optimax is much broader. If your project requires faster delivery or more challenging requirements, please contact a sales engineer at sales@optimaxsi.com for more information.

     

    General / Materials

    General/Materials
    Bounds
    Notes
    Lens Quality
    1-10 pieces
    3 quantities can be chosen for estimating
    Materials
    Optimax Preferred Glasses (in stock)
    If you are using OpticStudio, use the Materials Catalog OPTIMAX.AGF
    Glass Parameters
    Precision-quality glass is assumed in all cases
    Tolerances for refractive index, Abbe number, and homogeneity are not considered in the Cost Estimate
    Coating
    Limited to the coatings listed in the drop-down menu
    If using the Estimator through OpticStudio, you may select any OPTIMAX coating in the Coating Catalog

     

    Surface Parameters

    Surface Parameters
    Bounds
    Notes
    Surface Types
    Standard (Plano, Spherical, Conic), and Even Asphere Surfaces
    Even asphere coefficients up to 16th order are considered
    Radius (of Curvature)
    10 - 1500 mm
    Longer and shorter radii are possible, but out of the bounds of the Estimator
    Radius (of Curvature) tolerance
    0.025% or 1 FR (whichever is greater) for spheres; for aspheric surfaces, Rv ± 0.1%
    This tolerance is intended for surfaces with finite radii.
    Surface Power
    Minimum power tolerance is 1 FR.
    In OpticStudio, use the ISO 3/A tolerance for Plano surfaces. Optimax assumes the test wavelength is 632.8 nm.
    Surface Irregularity
    Must be >= 0.1 FR for planos and spheres, >= 0.5 FR for aspheres
    In OpticStudio, use ISO indication 3/B (irregularity, PV, in fringes). Optimax assumes the test wavelength is 632.8 nm.
    Surface R/number
    Must be >= R/1
    R/number = Radius of Curv/Clear Aperture. Faster surfaces can be made, but limited to R/1 for the Estimator.
    Surface Roughness/Texture
    Minimum surface roughness is 5 Angstroms RMS.
    In ISO 10110 format, Rq >= 0.0005 microns RMS
    Scratch/Dig
    Estimates are provided for scratch dig down to 10/5
    ISO Grade Number (5/A) must be >= 0.063 mm. Scratch width (5/L_A'') must be 0.001 mm or greater.

     

    Dimensions & Tolerances

    Dimensions & Tolerances
    Bounds
    Notes
    Diameter of Part
    5-100 mm (spheres/planos) 10-100 mm (aspheric surfaces)
    Diameter of Part, tolerance
    A total is calculated for -tol and +tol and it must be >= 0.010 mm.
    Traditionally, the +tol is 0; either method is acceptable
    Tolerance on Opening
    An Opening occurs for concave surfaces with sag faces. Tolerances on this diameter drive fabrication requirements on the surface sag where the sphere joins the flat. A warning will appear if the sag tolerance converts to < ±0.010 mm.
    In OpticStudio, the Opening is called the "Diameter"
    (Center) Thickness
    2-100 mm (2-50 mm if either surface is an asphere)
    Thickness may also be limited by standard glass strip thickness as supplied by manufacturer (varies with glass type).
    (Center) Thickness tolerance
    A total is calculated for -tol and +tol and it must be >= 0.040 mm.
    The thickness tolerance defines the range where power, radius, irregularity, and cosmetics must all meet specifications.
    Aspect Ratio
    2 to 12 (most parts) 4 to 12 (aspheres, and small parts with slow surfaces)
    Aspect Ratio = Part Diameter/Center Thickness; In OpticStudio, use Diameter (flat)/Thickness
    Clear Aperture
    Must be
    In ISO 10110, CA is called Effective Aperture. In OpticStudio, the part diameter is called "Diameter (flat)," and a convex Opening is called "Diameter"
    Edge Thickness
    1.0 mm or greater at part diameter
    Wedge (ETD)
    Minimum (total) ETD is 0.005 mm
    In OpticStudio, enter wedge in arcminutes as 4/S on one side only. ETD is calculated from that angle and checked against 0.005 mm
    Surface Decenter
    For aspheric surfaces, the surface decenter tolerance must be at least ±0.002 mm (ERO = 0.004 mm)
    In OpticStudio, for an asphere, enter both 4/S (tilt) and 4/L (decenter).

    LEARN FROM THE EXPERTS

    Want to learn more about the innovation and ideology happening here at Optimax Systems? Sign up to receive our Technical Papers.